|
Size: 2313
Comment:
|
Size: 3034
Comment:
|
| Deletions are marked like this. | Additions are marked like this. |
| Line 3: | Line 3: |
| = Rust embedded esp32 = * IDF - Iot Development Framework. * [[https://www.youtube.com/watch?v=o8yNNVFzNnM|YouTube]] => [[https://github.com/flyaruu/rust-on-esp32|GitHub]] => [[https://github.com/esp-rs/esp-idf-template|GitHub template]] * Check esp usb/serial connection {{ cargo espflash board-info }}} |
|
| Line 4: | Line 11: |
| * Links [[Sonoff]] , [[MicroPython]] | * Links [[Sonoff]] , [[MicroPython]] , [[mqtt]] , [[ds18b20]] , [[RabbitMq]] |
| Line 17: | Line 24: |
| * https://www.adafruit.com/product/2471 | |
| Line 59: | Line 67: |
| === Setup Arduino for esp8266 === * Have to download Arduino linux tar file * Un-tar and sudo ./install.sh to install * Add aditional board url "http://arduino.esp8266.com/stable/package_esp8266com_index.json" * Under boards, open board manager and search for esp8266, add * Now select board, NodeMCU 0.9 ESP-12 |
Rust embedded esp32
- IDF - Iot Development Framework.
YouTube => GitHub => GitHub template
- Check esp usb/serial connection {{
cargo espflash board-info }}}
esp8266
Links Sonoff , MicroPython , mqtt , ds18b20 , RabbitMq
https://learn.adafruit.com/adafruit-huzzah-esp8266-breakout/overview
- Small wifi electronic module ESP-01(WIR04001251) and ESP-03(WIR04001252)
http://www.hobbytronics.co.za/p/930/esp8266-serial-wifi-wireless-transceiver
3D wifi map http://hackaday.com/2015/02/17/mapping-wifi-signals-in-3-dimensions/
github project for ESP https://github.com/cnlohr/esp8266ws2812i2
LUA + programming http://vaasa.hacklab.fi/2015/01/12/esp8266-ds18b20-thingspeak-nodemcu/
2019 connect old esp8266 Huzzah
- Connect to usb using FDDI 3.3v cable (White usb plug)
Connect to serial /dev/ttyUSB using screen
sudo screen /dev/ttyUSB0
When i click the reset button on esp8266 i get the welcome message
NodeMCU 0.9.5 build 20150318 powered by Lua 5.1.4 lua: cannot open init.lua
Switch on red led on esp8266 using lua commands
gpio.mode(3, gpio.OUTPUT) gpio.write(3, gpio.LOW) #Pause red led on gpio.write(3, gpio.HIGH)
Program the HUZZAH ESP8266
For the HUZZAH ESP8266 breakout buttons for GPIO0 and RESET are built in to the board. Hold GPIO0 down, then press and release RESET (while still holding GPIO0), and finally release GPIO0.
$ sudo esptool --port /dev/ttyUSB0 erase_flash
Upload firmware
$ esptool --port /dev/ttyUSB0 --baud 460800 write_flash --flash_size=detect 0 firmware.bin ## Press hold left button, then click reset, upload begins. esptool.py v2.1 Connecting........_____....._____....._____....._____....._____....._____..... Detecting chip type... ESP8266 Chip is ESP8266 Enabling default SPI flash mode... Configuring flash size... Auto-detected Flash size: 4MB Erasing flash... Flash params set to 0x0040 Took 2.55s to erase flash block Writing at 0x00015800... (14 %) ... Wrote 615424 bytes at 0x00000000 in 67.2 seconds (73.2 kbit/s)... Leaving... Hard resetting...
Setup Arduino for esp8266
- Have to download Arduino linux tar file
- Un-tar and sudo ./install.sh to install
Add aditional board url "http://arduino.esp8266.com/stable/package_esp8266com_index.json"
- Under boards, open board manager and search for esp8266, add
- Now select board, NodeMCU 0.9 ESP-12
...